Perseus by Benvenuto Cellini - the sculpting technique (2)

The bronze casting

Before carrying out the casting, it is necessary to bury the mold. As it is so high, and as the molten metal is to be poured from the top so that it reaches by gravity the lower parts of the statue, there is no alternative but to bury the mold at the foot of the kiln where the metal will be melted. In addition, it provides a protection against potential mold burst when the two tons of metal will be poured. And it also contributes to a slower cooling of the metal, as the mold is uniformly isolated, so it improves the chances for the metal to reach the most remote areas.

Metal poured into a mold - Chammings sculptor workshop

 It took six months to bury the mold and build the huge furnace where the metal was melted. With  picks and shovels, to a depth of about four meters, the pit is ready. The mold is then lowered using a winch and a massive scaffolding. It was critical to avoid any shock to the mold as a crack would have forced to start over. After several attempts, Cellini, with its workers and with strong ropes, succeeds to position the mold in the bottom of the pit.The furnace itself was manufactured with the utmost care, taking into account the choice of bricks, their disposal, the general shape of the furnace, the volume needed to accommodate the entire metal, the necessary openings for pouring and combustion of the metal and the opening hole to pour the metal into the mold.

Cosme 1 de Medicis, portrait by Pontormo - 1518

Five years had passed since Cosimo had commissioned Cellini 's Perseus . The tension was high with the Duke. Cellini was the subject of a conspiracy with his project that all qualified as foolish and undoable. Nevertheless, Cellini resists, his glory and honor is at stake if it fails, he would be banished from Florence and could no longer perform his job.The day of casting, the mold is buried with a mixture of soil and sand. The openings in the mold are extended with stoneware pipes so that they are not obstructed by the soil and allow the evacuation of air and gas. It is important to proceed with the casting as soon as possible before the moisture attack the mold. Ingots of copper, brass and tin (two tons in total) are arranged in the furnace. Cellini's entire team is at work .

The fire is lit and the metal begins to melt and boil. But the oven gives off so much heat that the thatched roof starts to burn. The rain, which began to fall, helps to contain the fire, however, it threatens to penetrate into the mold, which must be avoided at all costs. A battle against the fire starts immediately.

After several hours of hard work, and Cellini close to exhaustion, the molten bronze began to coagulate, making it impossible to flow. Cellini throws into the furnace oak logs that generate more heat. He managed to break the bronze crust that formed on the surface, but the overheated oven cover explodes and revives the fire. They need to cast as rapidly as possible. The metal is too thick and does not flow fast enough. Cellini then added tin and finally the mold begins to fill. All the metal contained in the furnace is used. The mold is completely filled. The cast is completed.

After two days of cooling, the mold is cleread from the soil around it, and taken out from the pit with the same winch that was used to take him down. Cellini begins to break the mold to reveal the statue. As Cellini had expected, only the right foot of Perseus - the most remote area from the opening hole - had not received enough metal. The following months will be devoted to the completion of the foot, to cast the sword and helmet wings and sandals, to fix them to the statue, to carve the damaged details from the melting and then the surface polishing.

The Base

Cellini had planned to complete his work with a majestic marble base three meters high. He set four niches of about one meter on each side of the rectangular block. In the niches, he created and displayed statues of Mercury, Minerva, Jupiter and Danae with her son Perseus.

The block itself is carved with various motifs like shaped garlands, ram heads, shells and goddesses' busts. The finishing touch is a bronze bas-relief depicting Andromeda liberation by Perseus, on the stand base.

Unveiling

It took another five years to complete the base and install it under the arcade of the Loggia dei Lanzi. The transport of the three heavy sections, Medusa, Perseus and the base is delicate and difficult. It also attracts curiosity. Cellini resists the pressure to disclose his work until all pieces are linked together. The tarp covering the work is finally withdrawn on April 27, 1554, nine years after the order. Without ceremony, Perseus appears to the crowd of onlookers. It is triumph. Cosimo I even expressed his satisfaction at Cellini.

However, the payment for the statue is a cause of further tension between the two men, because of poorly conducted negotiations. Cellini will never get any more order of that importance. Now considered a genuine masterpiece and a technical major achievement, Perseus always throne to its original location. The work has been the subject of a restoration in 2000, for the 500th birthday of Cellini.

Perseus by Benvenuto Cellini - the sculpting technique (1)

 

This post will be a little longer than usual, as it tends to describe (adapted from French Wikipédia) the whole process to create this stunning Perseus sculpture.

The thinking process before the sculpture

Because of the many fragile parts (sandals' wings, sword, raised arm with Medusa head, etc.) to be sculpted in marble, Cellini decided to do a bronze sculpture, despite the planned height of 6 meters.
To facilitate the making, and also for aestethic reasons (as the proportions for a 6 meters statue would have been too disparate) he divides in 2 the planned height. From right foot to Medusa head, the final height will be 3.20 meters, in addition to the 3 meters base to be sculpted.

Cellini is willing to cast the statue in one unique piece, even though it is a very imposing height, as he wants to avoid the problems encountered by Donatello and his Judith sculpture. That sculpture was made with 11 different parts, melted separately then welded. But doing this it was showing variations in colors, in thicckness, and the weldings were too visible. Cellini did not wanted that at all.

Also, as the Perseus was planned to be located below one arcade (see picture below), and not leaning against a wall, Cellini wanted the sculpture to be beautiful and full of harmony from all faces. Eventually, he wanted to sculpt the 4 faces from the base with bas reliefs, to develop and enrich the myth.

 

Steps

Cellini will first start with the Medusa head, then Perseus, then the base. The challenge is enormous, because the technique to mold a bronze statue so high was lost since Antiquity.
To succeed to cast the statue in only one piece, Cellini will use the lost wax technique, in which the sculpture is made in wax, on a mold in clay. The was is then covered with clay. Then the wax is melted and lost. Bronze is then cated between the two layers of clay. Once the bronze is cold,  refroidi, the outside mold is broken to reveal the sculpture.

Medusa

 

Before to start with Medusa bronze, Cellini does some experiences, like with the clay to be used for the molds. He does a Julius Cesar bust, which confirms his choices. Then, to be fully sure about his technique, and to please the Florence Duke, he does a Cosme I^er bust.

Now that he is 100% reassured on the clay quality, he starts the Medusa cast. As she has to stand on a small surface,  he decides to display her body on a shield and on a cushion.The cushion reminds the bed on which Medusa was surprised by Perseus while she was sleeping.

The shield evokes the one that Athéna gave to Perseus to allow him to be close from Medusea without being transformed into stone. Legs are folded in a unsual angle, while the left arm grips one ankle, and the other arm lays lifeless along the base. From the beheaded neck, a river of blood leaks, quite a strong vision for that time.

It takes Cellini two years before to unmold Medusa. The result is impeccable. It earned him the esteem but also jealousy. Cellini must even defend his project with the Duke, who is very impatient and has doubt, like the others, about the ability to cast the imposing bronze Perseus. Cellini succeeds to persuade him with lots of technical arguments, but the relationship between the two men remains fragile.

 

Perseus

Despite the tension and fear of failure, Cellini starts the making of Perseus. Because of its size, the statue must be empty, otherwise the weight of the bronze would make it impossible to move. To do this, it takes a special mold.

Cellini first solidifies the mold with iron bars, to support the wire mesh that draws the first contours of the statue. It then prepares the clay that will cover the trellis. This clay, taken near Florence, has been carefully chosen and prepared first with pieces of sheets. After mixing them until a smooth paste, Cellini sprinkles and knead it for several months. The wad of cloth eventually rots and provide a smooth creamy mixture, easy to work with . The resulting clay will dry evenly without risk of causing imperfections in the casting.

When ready, Cellini applies it on the frame and shape it for several hours to form the earth core of the mold. Before being coated with wax, it must be perfectly dry. The mold is first left to dry outdoor, without cracking. Then, it is heated in the fire to remove any moisture that might burst the clay at the time of casting bronze.

The next step is to cover the core with a layer of wax of similar thickness to that of the desired metal sculpture. Soft wax is also used to shape the details of the statue (face, muscles, visible veins, etc.). The wax itself is the subject of careful preparation. It should be smooth and tender at the time of application. It must then dry securely to withstand the weight of clay that will cover it. No error is allowed, because the final result depends heavily on the shaping wax.
Once this work is completed , which already shows the final appearance of the statue, the core and the wax need to be covered with clay. At this point, it is important to provide a system of tubes through which the molten metal goes down into all areas of the mold, while allowing air to escape. These tubes are also made ​​in wax , before being covered with clay.

Cellini in his workshop working on Perseus project

To avoid damaging the wax, and therefore create damage to the sculpture, the was must first be covered with a protective mixture made of ... marrow from calcined horn sheep bone, with plaster, Tripoli rock powder, iron filings, water, all that filtered through a sive made of horse manure!

The resulting preparation is applied using a brush made ​​with pig bristles. The operation is repeated several days, layer after thin layer, allowed to dry between each application. This protective layer may then receive successive clay coatings, while maintaining the drawing of the wax, now well protected.

Now, the wax trapped between the core and the outer layer needs to be removed. It is this gap which will then be filled by the bronze at the time of casting. A first fire drying takes place. Then, a stove of four meters high is built around the mold to finish drying.

The wax flows through the tubing created by the wax sticks . The mold is now ready to receive the bronze.

Part 2 will show the last part of this sculpture achievement, and the reactions once it was unveiled.
 

Perseus by Benvenuto Cellini

The Perseus by Benvenuto Cellini is a dream for a sculptor, both from the aestethic point of view, superb, but also due to the techniques used to create this masterpiece close to 10 feet high (without the base). And for a gay perspective, well, it is a very nice muscular body, from head to toe... :)

The following text is adapted and translated from Wikipédia (English and French as both versions do not focus on the same elements) - the French version describes in details the sculpture technique used by Cellini like a thriller!.

 

Perseus with the head of Medusa is a bronze sculpture made by Benvenuto Cellini in 1545. It lays on a square base, and is located in Florence (Italy), Piazza (place) della Signoria.  That imposing place had already stunning sculptures such as the one in pure Carrara's white marble 'David' from Michelangelo and others.

 

 

Therefore the Duke of Florence, Cosimo I de Medici, wanted to leave a strong and lasting impression with his new commission to Cellini, who just left France and the king François I to come back to Florence.

Bust of Benvenuto Cellini, by Raphaello Romanelli (1901). Picture by Thermos.

 

The subject choosen by Cosme I is the mythological story of Perseus as it contains numerous symbols he wants to exploit such as Perseus strength, courage, overcoming all challenges, fearless, his destiny, and beauty's victory over ugliness. Cosme I asked Cellini to sculpt Perseus raising Medusa's head in his hand, as it would symbolize Medici's victory over Republicans, and superiority of good over evil.

The Wikipedia description of the statue : " Perseus stands naked, except for a sash and wingel sandals, triumphant on top of the body of Medusa with her snakey head in his raised hand. The body of Medusa spews blood from her severed neck. "

These 4 great photographs are from Andre Durand Digital Gallery. See his website here

 

 



Christopher park and the 'Stonewall' gay sculptures from George Segal

Almost 35 years ago, in 1979, pop sculptor George Segal was commissioned by the Mildred Andrews Fund, a private Cleveland-based foundation that supports public art, to create a sculpture that would commemorate the famous 1969 rebellion in front of the Stonewall bar in New York.
That rebellion and riots marks the beginning of the modern gay liberation.
Below are some pictures of this life-size sculpture.

Picture by Wally Gobetz

Picture by Yotsuba

                                 
One plaque gives credit to the sculptor and foundation, and another one allows the public to know more about the location, the bar, the park, the artist, the foundation, etc. The long text is part of the NYC Historical Signs Project.

                                    

Below is a photograph of a sculpture copy, installed on the Stanford University campus in Palo Alto, California (copyright Ingrid Taylor).

George Segal biography and more détails on his artist's life and works can be seen in wikipedia here and at the Artist's Cafe here. A retrospective was also held in 2002 at the Hermitage in St Petersburg (see here).

Patrick Poivre de la Freta, my sculpture teacher - mentor - coach

I committed to talk a little about him before year end, so here it is.

Male love was his oxygen, .............  A real artist, in many directions. As a painter he opened two galleries in France - Brittany and St Paul de Vence. He mastered silk painting, for Givenchy and others. Had several 'periods' in his painting career, such as abstract, onirism, surrealism, lyric expression, figurative. He was a student of Salvador Dali in Paris. Also active as a writer, as a sculptor, creating furniture design, numerous frescoes and trompe-l'œil, as well as a wall mosaic like the one below in a bathroom (private collection).

                                     

                                    

Patrick was my sculpture mentor and coach, and I will forever be grateful for the time spent with him, receiving his guidance and encouragements to pursue and develop my sculpture work.

I was regularly bringing to his studio my work in progress, to spend a few hours while he was painting or drawing or writing, and checking from time to time my clay or stone work, showing me how to better express a neck move, insisting on the tension to be shown to be more expressive, and even to dare do large cuts! As an example, below is one of my sculptures in his painting studio.




I would not sculpt during almost my full -available- time today if I had not met him.
So, thank you, Patrick !

The photo below shows Patrick in his home and studio, taken after lunch and some flavoured rhums... together with Eric, one of his models for the major sculpture project, the Ignudi

 

Below is one of Patrick's 20 Ignudi waterlocors, choosen for Pascal's pose.

 

The next 3 photos were taken during one of the photo shootings, showing Pascal then Eric, posing under Patrick guidance for 2 of the Ignudi planned sculptures (pictures of models are published with the models' approval - all rights reserved).

 

Patrick last project : to sculpt the 20 ignudi from the Sistine Chapel!

Michelangelo painted Chapel Sistine ceiling during four years (between 1508 & 1512) at the commission of Pope Julius II. Initially he refused to do it, as he considered himself more of a sculptor than painter (and we will see in future posts some sculpting masterpieces of nude male sculptures from him). But forced to do it, he negotiated to get a total freedom for this giant work.

"The Ignudi are the 20 athletic, nude males that Michelangelo painted as supporting figures at each corner of the five smaller narrative scenes that run along the centre of the ceiling. The figures hold or are draped with or lean on a variety of items which include pink ribbons, green bolsters and enormous garlands of acorns." ...        "Their painting demonstrates, more than any other figures on the ceiling, Michelangelo's mastery of anatomy and foreshortening and his enormous powers of invention." (source Wikipédia).

These 20 «ignudi» have been with Patrick for many years, as he started with a serie of watercolors called 'The Sistine Chapel revisited' from the early 90s.  Then he wanted to include them in his next adventure!

Indeed, aged 65, Patrick envisioned his latest artistic challenge, in sculpture. He felt that, maybe, Michelangelo would have loved to sculpt these 20 nude sitting men. Patrick's contemporary 'twist' was to take models living or visiting regularly St Martin, to add a contemporary item linked to the model, and a body pose matching fully the Michelangelo characters. Below one of the character in clay, and a detail of his first bronze.

Patrick planned to do all these sculptures in 2010-2011. But unfortunately a sudden unexpected cancer stopped him in March 2012.

         

                                                                                                               Photo Jean-Marc Riva.

Tropismes Gallery, and Art Lovers

Patrick was a co-founder of Tropismes Gallery, in Grand Case, together with Paul Elliot and Nathalie Lepine, gallery which displays contemporary art pieces from local and international artists.
During 3 years, he also acted as secretary of Art Lovers Association, founded by Denis Thuleau, which promotes the St Martin island's artists and organizes each year the Art Lovers weekend, during which most of artists' studios are open to the public.

Some highlights 

Born in Paris in 1944, he won a few prizes in poetry during his youth and started to paint. He spent 2 years in the French navy (theme which can be seen in many of his paintings), and opened his first gallery in Brittany at age 33. He was a student of Salvador Dali. Then opened his second gallery in St Paul de Vence. Many personal exhibitions in France, Los Angeles, Brussels, Munchen, Chiraz Persépolis Festival (Iran), Montréal, Ottawa, Chicago, Caribbean islands. Moved to St Martin in 1997. Patrick's legacy for all image rights from his paintings, drawings and works in general has been given to Yves Carteau, photographer.

Antinous (6) Contemporary versions!

 A superb contemporary large private wall mosaic, by the artist Shawn Postoff.

Another sculpture style by the Mexican artist Enrique Estrada.

 

And another version of contemporary art, this time a 'sculptured engraved glass'.

Copyright Othmar Rohm.

 



Antinous (5) Exhibitions & links

In 2012, the Villa Hadriana in Tivoli (Rome) organized the exhibition called 'Il Fascino della Bellezza' (Antinous, captivated by beauty). Catalogue available at IbsIt.

Previously, other exhibitions included :

In England, at the Henry Moore Foundation : 'Antinous: the Face of the Antique'
Exhibition 24th May 2006 - 26th August 2006. Catalogue available on Amazon.

In Berlin, in 2005, at the Pergamon Museum, 'Geliebter und Gott' (Lover and God).
Catalogue available at WorldCat.

Still in England, at the British Museum, 'Hadrian Empire & Conflict.
24 July - 26 October, 2008. Catalogue available on Amazon.

 

 

 

Some links :

 

Among the dozens of websites or blogs telling the love story between Antinoüs and Hadrien, or related to the arts and architecture projects from Hadrien era, here is a few:

 

Antinoos info and the virtual museum displays a comprehensive collection of Antinoüs portraits, paintings, sculptures etc. sorted by country and town.

 

The Farnèse collection from the Archeological Museum of Naples is well described here by Auror art & soul.

 

The online database of ancient art allows extensive search by artist or period.

 

The artist and designer John Coultart in his feuilleton listed some of the exhibitions about Antinoüs.